Samsung Galaxy S
The tutorial that we present below, as update Samsung Galaxy S through Odin to the firmware 2.3.6 and its corresponding Root, it will serve, among other things, to install the ClockWorkmod Recovery in our GT-I9000, to later be able to install any Modified rom and optimized for our terminal.
The first thing we should check is whether our Samsung Galaxy S has access to mode DownloadTo do this and with the terminal completely off we will turn it on with the following combination of buttons, Vol minus + home button + Power button, we will press them at the same time and without releasing them until a screen like this appears:
Access Download mode
If so, we will be ready to install the firmware JVU with Android 2.3.6 using a tool that will become basic and essential for our Android, the tool is none other than Odin for Windows.
For exit Download mode all you have to do is hold down the power button for about ten secondss, or failing that, remove the battery for about five seconds and put it back in.
Preparing for installation
Keep in mind that by following the steps in this tutorial You must take full responsibility for what may happen to your device, If you stick to the instructions here, nothing bad should happen, but to think that every time we enter the internal system of our Galaxy there is a risk if we do not do things as indicated.
Also before starting this tutorial you must have the battery charged from your terminal to 100 by 100.
We must have all the drivers installed correctly in our PC, if you have installed Kies and you have successfully synchronized your terminal on some occasion, you will already have the necessary drivers installed, if not, go to the official website of Samsung and download the latest official version of this program and install it and synchronize your device.
Kies official Samsung program
The first thing we will do once we have verified that we have access to the mode Download, will be to download all the necessary files to carry out this tutorial successfully, for this we attach the links to both the Odin program for Windows and the official JVU Firmware and its corresponding CF Root.
Below I leave you the link to an essential file called Pit 512, which is essential for Flash using Odin of our Galaxy, usually comes within the tablet of the firmware or of CF Root, but as I have sometimes found myself with the unpleasant surprise that this essential file was missing, I am attaching it individually so that you can keep it safe.
Once all the files are downloaded, we will unzip all in the place of our Pc that we like the most, I advise you to create one new folder on desktop and unzip them all inside it, all except the last file, since it is not compressed.
Now in this step we will go to the menu of our Galaxy S and activate the USB debugging, which is in the following path: Menu / Settings / Applications / Development.
Once all this is done we will be able to update through Odin of our Galaxy S to version 2.3.6 and install its corresponding CF Root.
Firmware installation method
First of all we will check that Choose is completely closed, for this we will open the Windows task manager and we will finalize any process that has to do with Choose, simply by looking at the names of all open processes, if any included the word Choose somewhere we would close it too.
Now we will run the program Odin and it will show us a window like this:
Odin home screen
Next we will place the files in the Firmware folder as follows:
- We will place the Pit file that we download last in the button of the same name, for this we will click on PIT and-navigate to the path where we save it previously.
- In the PDA button we will place the Code file of the unzipped firmware
- In the PHONE button we will place the MODEM file
- In the CSC button we will select the file called CSC
We will check that the type boxes Checklist options are marked on the left Division, Auto Reboot y F. Reset Time.
For more security check the image attached below:
This is how Odin should look on you
Once everything is checked, we will turn off the Galaxy completely, and we will turn it on using the button combination mentioned above in Download mode, we will connect it to the PC and check on the Odin screen that it has recognized it correctly, for this it will show us the word COM followed by a number just in the upper left.
Now we just have to press the button Home and do not touch anything until the process ends and in the upper left part report the word Passport, It goes without saying that we should not, during this process disconnect the phone under any circumstances, as well as preventing our computer from entering or suspension, neither hibernation Nothing like that.
The process may take a few approximately five minutes. Until we see the word PASS not touch anything, once he gives us Passport we can now disconnect the phone from the computer and wait for it to restart.
CF Root installation method
With the previous step you will have the Galaxy updated correctly and fully functional to the version Android 2.3.6, in this next step, we will dedicate it through the same tool to install a Custom kernel with the Root and ClockWorkmod Recovery installed.
After this process we will have the Galaxy ready to install any compatible Rom through the modified Recovery.
We will open Odin again, if we already had it open before, we would close it and reopen it, this time we will place the file inside the folder CF Root, in section PDA Odin, and we will not select any more files.
We will check that Re-Partition is not checked this time, the other two options should be selected, so that there is no doubt I am attaching a screenshot of how everything should be this time:
This is how Odin should look on you
Once verified that everything is as in the attached image, we will turn off the Galaxy and we'll turn it back on Download mode, once turned on we will connect it to the PC and we will give the option Home from Odin's window.
This time the process will take less than one minute, as soon as Odin gives us back the word PassportWe can now disconnect our phone from the computer and wait for it to restart.
With this we will have Rotated, Modified recovery and updated to version Android 2.3.6.
Stay tuned for new publications as I will be presenting you the best Roms for our device, both the Gingerbread like the most recent Ice Cream Sandwich with android 4.0.
More information - Samsung will not update its Galaxy S with any value pack
Download - Choose, Odin, Firmware, CFRoot, Pit 512.
This is an event?
This works for 9003? Greetings
It does not work, each terminal has its own firmwares
How do I do if I put my cell phone to format in odin and a green line does not happen…. c ah remained as marked, what do I do in that case 🙁
I'm seeing that the post is several years old and I don't know if you get to see this message.
This is the first time that I have found a coherent explanation of how to recover an i9000.
By the way, my problem started when I ran out of service. It turns out that the IMEI changed to 00499… ..
This all comes because I'm trying to rotate (superuser) and it won't let me. If you have any advice I would really appreciate it.
My email: aantunez@tsj-dem.gob.ve.
regards
I did this to my phone and it died it was a 9003,
How do I revive it?
To start this tutorial is for the Galaxy S, or GT-i9000, as you started flashing the gt-i9003. The first thing you should do is check if it is valid for your model.
Check if you still have access to Download mode, if so, you can still re-flash it with the correct firmware.
I can't give life to my mobile It happens to me the same as most of you. The phone turns off and I can't turn it on again, even in download mode! I hope someone gives me a solution! 🙁
the link to the CF root is broken ... any alternative?
milks! Why have you deleted the update to ICS post?
no joaquin, no good for 9003
Thank you!
The link of the CF file is no longer valid, could you repost it?
It is already re-uploaded
Does anyone know why it takes so long, ievo like 20 mins I still designed SBL in the upper left part and in the bar of my galaxy only a tiny percentage goes, does anyone know why ?? what I do? I would thank you a lot.
regards
How did I finish the thing friend, did you start well?
the CF file is no longer available
Can you upload it again?
the CF file is no longer available
Can you upload it again?
It tells me pass, but when it starts it appears on the screen ON SCREEN KEYBORD SETTINGS but the screen does not work apparently because of the pressure and it does not give answers, what do I do?
What model of phone do you have compi?
very good everything, perfect explanation.
Thanks recommended
everything was perfect and in a very short time, thank you very much.
Thanks!!! everything worked perfect ... the only thing is that I don't know why, but the 3G doesn't work for me .. I don't know if it was because of the update or because there is something wrong ... I would appreciate any suggestions! SAlu2
In case it still works for you.
3G wasn't working for me either and what I did was call my company (Euskaltel) and by phone we configured the section of »Mobile Networks - Access point names - Create a new access point» and from there I filled in the data What they were telling me, now the 3G works for me.
I have had a problem that seems quite serious. : S
It has failed to install the CF ROOT and now it does not start me. I see an icon of a mobile phone connected to a pc with a danger sign (yellow triangle with exclamation mark) between them. I try to turn it off, go into download mode ... but there is no way. I have also removed the battery but when I put it back, the happy icon appears again. What can I do?
Well, I managed to get out of the semi-brick that I had entered. I have removed the battery and SIM for about half an hour. I put the battery back in (not the SIM) and tried to enter Download mode. It has worked for me. Then I have reinstalled firmware 2.3.6 with Odin and the phone is resurrected. I do not know where I could have made a mistake but after the scare I think I am not going to install the CF ROOT 🙂
A greeting and thanks
For those who appear the semi-brick with the image of the triangle and the computer, or those who have problems with the sbl process, that the installation in odin no longer advances, here I leave you a very good tutorial http://www.carvax.com.mx/2012/01/26/reparar-galaxy-s-i9000t-de-semibrick/
And if we don't have access to Download mode?
Hi look, I did everything following the steps until the screen went dark in the download mode when odin finished, and I disconnected it. now it does not turn on, does not charge or shows signs of life. Can that be fixed?
Did the odin give you the PASS?
The same thing happened to me: I know what you did ???
The same thing happened to me as you fixed it
Help me
for it to continue living you have to follow the instructions, but when you take out the battery, turn it on with the combination of keys and the download from there will appear again. You continue to install the rest—– it's not dead !!! only in a coma hehehej yeelzu_22hot
I did update it but now the network does not recognize me, I can call but I cannot use the Internet I cannot configure my mail at all? what should I do?
Enter wireless connections and configure the APN data, calling your operator they will provide them.
friend what is the firmware password ??? del pda, phone and csc to unzip the rar file
samfirmware.com, puts it in the post
What did you do to solve it? If it is, does it have a solution?
configure APNs from mobile networks settings
Hi look, I did everything following the steps until the screen went dark in the download mode when odin finished, and I disconnected it. now it does not turn on, does not charge or shows signs of life. Can that be fixed?
What did you do? The same thing happened to me yesterday ...
the problem is that the model of your computer is not the same as the one in this post, the same thing happened to me, the title of this post is not clear, you can make those mistakes, my computer is a galaxy S gt-i9003 , this post is made for the gt-i9000 model. Sorry to tell you they bricked your cell phones and to fix them you have to use a special circuit connected to the phone's USB cable. As I had bought the cell phone recently, it still had a warranty, so I took it to the technical service and when they discovered that it was a logical short-circuit fault, they changed it for a new one.
Hello, I already have the mobile up-to-date and everything works well, but when I want to download the CF Root, it appears that it is supposedly coupled to another program, ok, I download that program, I installed everything but the CF Root is nowhere, could you help me ... ..
Hello Francisco,
A great post!
I've gone from super novice to super user in a flash! But I have the same problem as bonilla18luis, and despite having the roaming activated it does not connect to the network, and in mobile networks I connect to my network (Boda fone) and it remains the same ... Also looking around the APN configuration (http://www.vodafoneteayuda.es/2011/12/habilita-la-conexion-a-internet-en-tu-terminal-con-android/) I can't do it either ... I could use a little help!
Greetings from the Raval and thank you very much !!!
In the BLOG you have a Post on how to configure the apn
On 06/11/2012 04:35, «Disqus» wrote:
I don't have that option !!! what I do
Enter Settings / Wireless and networks / Mobile networks / Apn and create a new APN with the data that your company will provide you.
Help ise all the steps and I turn it on and I get on-screen keyboard settings and it does not let me advance
inside the CF ROOT SALE zIMAGE folder, BUT IT DOES NOT ALLOW TO DO ANYTHING IN ODIN… CAN YOU POST AGAIN?
That's because you unzip the .tar file and you don't have to unzip it, you must use the cfrootxxxxx.tar in odin.
The same thing happens to me and I don't know how to fix it.
Cfroot is not a folder, it is a .tar file, and it is the one that you have to use directly in odin.
Thank you very much
Hello, very good evening friend, a question I have installed this version 3 times and something very strange always happens to me I have read almost all the comments and I think it only happened to me and it is the next thing that when I turn off the equipment or restart it after turning it on, it stays Without multimedia sound, I mean, the bell rings when a call comes in. Facebook notifications and other chat things the only thing that does not sound is the multimedia volume and the system volume, the notification and the incoming call, also work perfectly and I no longer know what do if you know what happens please help me that I think is a very good version since I have installed others and this is the best for my opinion thank you very much if you want to help me please add me to my fb victor860609@hotmail.com thanks and regards
When restarting, it asks me for a password, it says confirm password.
I guess it will be the Sim
very well everything went perfect !!!!! now my SGS has facial recognition, the photo editor, the sg2s unlock and taking photos and recording videos good tuto now I'm going for the update post that you just uploaded !!!! Congratulations !!!!
Hello!! I have a little problem with all this, and I do not know if it puts me in download mode, since I do the combo of the three buttons and I get a menu without download option nor do I get the android with the shovel, even so I put it in the odin detects it to me, I put everything in its place I give it to start and everything begins to work but it remains in setupconnection .. so you can paste hours. What can I do, thank you very much !!! I leave you my email iavp79@hotmail.com. Thanks again
Exactly the same thing is happening to me, it got caught in SetupConnection and it won't work ...
I answer myself in case it works for someone. The password is the one you use to unlock the screen (not the pin of the mobile network)
Do you have the terminal rooted?
Regarding this problem, I have a rotated terminal and it stays in setupconection, what can I do?
Hi, I made the first step and my screen went dark and supposedly it had to restart, what do I do now?
friend what did you do The same happened to me
did you solve it?
The same happened to me….
did they manage to fix that?
The problem is that the model of your equipment is not the same as that shown in this post, the same thing happened to me, the title of this post is not clear, you can make those mistakes, my equipment is a galaxy S gt-i9003 , this post is made for the gt-i9000 model. Sorry to tell you they bricked your cell phones and to fix them you have to use a special circuit connected to the phone's USB cable. As I had bought the cell phone recently, it still had a warranty, so I took it to the technical service and when they discovered that it was a logical short-circuit fault, they changed it for a new one.
friend what is the firmware password ??? del pda, phone and csc to unzip the rar file
thank you very much!
Thank you friend
On a Samsung Galaxy S Captative i897 can this procedure be performed? I read GT-I9000 above and since I am new to this, I have no idea about Andriod phones. Could someone tell me if I have firmware 2.3.5 can I upload to 2.3.6 with this method?
you can't, they are different devices.
Not this is only for the GT-i9000
a question when returning root will all data and applications be deleted?
Like several who posted below, after I got PASS in the update of the android, I got stuck and afterwards it did not turn on or give any signs of anything, I removed the battery, I tried with recover and with download and it does not give signals! What can I do: S
I have a Samsung Galaxy S but the version that has a Digital TV Tuner. If I apply this procedure, will I continue to have access to the TV? Thanks a lot!
I do not believe, friend, everything that is not an official update, I do not believe that it carries that application, I do not even know it.
Anyway thanks for answering me.
For those who are in a semi brick you have to do all the steps of the firmware installation and then at the end enter the cell phone settings and place the usb debugging again otherwise the cf root will not accept them in odin
Dear do all the steps, when I disconnected the cell phone the screen was dark and it does not respond… I removed the battery and it does not respond or in download mode
What am I doing?
Thank you
Let it rest for a bit without the battery and go back into recovery mode, and flash everything again, paying special attention to the first flash to mark the Re-partition, and in the second, that is, in the Kernel or cfroot, if not mark it, I repeat do not mark the re-partition
hello I have the galaxy player (ypg70) and a week to now it does not play multimedia; It does not play music (it crashes and an error appears in the application), the alerts do not sound, I cannot record voice or video, it does not play YouTube (a black screen remains) or the radio. It is worth mentioning that I have 3 weeks with him, they gave it to me (if I do not have the invoice to send it to the service / warranty center) ……… through chat support with samsumg staff I reset it to reach the values of factory and nothing was not fixed the problem …………. can you help me?????
Does it enter Download mode?
Starting with the terminal off, turn it on by simultaneously pressing the Volume buttons down plus home plus power, and tell me if a yellow symbol appears with an Android under construction.
I followed the instructions to the bottom of the letter and the touch does not work…. help please.
What is the Touch?
the touch screen does not work…. I get a confirm password and I can't do anything, I turn it off and it comes back. please help
Re-flash from the beginning paying attention to all the steps.
What you tell me about the pasword I have not heard in my life.
The same thing happened to me, how did you solve it?
I don't know what you mean, specify a little more.
Anyway, I would flash again.
The same thing happened to me, the touch screen does not work, no matter how much you give it and give it, the touch screen does not respond ... do you know if there is a solution?
Is it necessary to be root?
Is it necessary to be root?
No friend is not necessary
Good morning. I have the s2 released and not free for a store. I cannot update it and I always have to take it to the store. I am not charged but it is a pain in the ass. I imagine this program could do it but the symbol of android working. only warning appears… .etc.what can I do please?
You can unlock the Samsug Galaxy S yourself with the Galaxy Unlock that you will find in the Play Store.
A query, I have done everything in the tutorial passes this:
OSM> MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
Checking MD5 finished Successfully ..
Leave CS ..
Odin v.3 engine (ID: 4) ..
File analysis ..
SetupConnection ..
Initialzation ..
Set PIT file ..
DO NOT TURN OFF TARGET !!
They go like 20 min and it hasn't moved at all, it keeps saying SET PARTITION in the box above and it doesn't load anything .. should I keep waiting or what do I do?
PS: It is Galaxy S 9000
Hi Yamiztc
I have the same problem that you indicate
Could you solve it?
Thank you
Settings menu / connectivity / mobile networks / apn, if within this route no option appears, click to add a new APN and in the first option put Yoigo internet, then in the second you put internet, press the back button and select the APN that we just created, restart the Galaxy and problem solved. I hope that it will serve you by the way I tried version 4 but in the calls with viber they did not hear me but calling normal if that works, I also tried other programs and nothing goes like a shot version 4 greetings
I did everything as the tuto, odin gives me the pass, the cell remains on a black screen, remove the battery and it does not turn on or in download mode, please I'm desperate, 2 weeks ago I bought it
You are very great man, I did it as you said and I had no problems.
Thank you very much and a very big greeting.
Thank you friend.
I followed your steps to the letter and the touch screen does not respond ...
The same thing happened to me, I need to know what to do, my phone says confirm password… and the touch doesn't work for me.
It happened to me exactly the same!!!!!! Could you fix it? T____T
The same thing happened to me wn .. they still haven't fixed it ???
how they fixed it hell: '(mine is a samsum galaxy S i9000
Question, How do I make the data network work? I enable it and it does not appear ... I never had the need to configure any APN because the same device automatically connected the data network, and if I add an APN it asks me for details that no idea, will there be any way to make it work? By the way, my cell is free…
Call your company and ask for the correct information, they will not give you any problems.
I did everything and now the touch does not work for me .. (touch screen) when I turn it on to configure I can not do anything that I do.
What is the model of your terminal '
Felipe I just went through your case, my screen had died because it turned on but it did not work to the touch but wonderfully I found this video and it was the solution !!
works for the i9000T ??
Thank you very much indeed.
Last night my mobile was blocked on the home screen, it did not charge or anything. It didn't even go into the recovery mode, but it did in the download.
I have followed in your footsteps and thanks to you my mobile has been resurrected.
Thank you very much really.
Hello I would like to know if this rom is applicable for galaxy s GT-I9000t
No friend this rom is for the i9000
Thanks Friend, can you recommend some rom for my cell. since I need to update I have a vers. froyo 2.1.1.
Look for Team RemICS-UX which is on the blog
hello friend do you know where I can get an ICS rom for my gt-i9000t since you clarify that it is not for this device… thank you!
Hello good friend, I told you that I took a risk and installed the rom even though you told me it was for GT-i9000 but even so I installed it and the rom works for me on my Gt-i900t, it is working normally.
I'm glad it works for you, but is everything okay?
Send by Samsung Mobile
Disqus wrote:
Juan Carlos Rosales (unregistered) wrote, in response to FranciscoRuizAntequera:
Hello good friend, I told you that I took a risk and installed the rom even though you told me it was for GT-i9000 but even so I installed it and the rom works for me on my Gt-i900t, it is working normally.
link to comment
IP address: 186.32.65.141
I don't know what I'm doing wrong, but I have followed the steps to the letter and when the update starts in ODIN it hangs in "boot.bin". The blue progress line on my terminal does not exceed what should be 2%. I have tried again and the same. What can i do to recover it??
i just tried installing it on galaxy S gt-i9003 and it got dead
I'll have to use the guarantee and say I never touched it but hey
I already experienced that any rom does not work even if it is galaxy S
Make it clear that it is for the GT-i9000, check if you have access to download mode and you can still save it.
I don't have access, he's completely dead ...
Friend followed all the steps and when I use several applications and go to the main screen it stays in a loop that the screen goes black and the wallpaper comes out again and so indefinitely what would be the solution?
Hola!
I have followed all the steps and when in ODIN I give Start it shows me a windows message (red cross) that shows the path and the CODE file and an OK button. If I accept ... it stays as it is working and in the ODIN message box it shows Please wait .... I have waited more than 20 minutes and nothing appears to tell me that it is processing something ... what should I do ??? If I don't press ACCEPT, it doesn't do anything either ...
Despite the recommendations that I do not touch anything ... after 20 minutes, I decided to close ODIN, and turn off the mobile ... and everything remains the same as before I started, I mean my mobile works and that but you never see that it has updated the firmware . My mobile is a Galaxy S I9000
I hope you can help me… ..
Do you put the mobile in Download mode?
Hello, I would like to know if Samsung has a voice reader such as the iPhone called (VoiceOver) this application is for people with low vision, we have searched for it to use it in the samgus and we do not have an equal and we would like to know if there is the possibility of loading it or not since we prefer the samsung ... nc if this iphone application is under another name, thank you in advance for your answer ...
fit for gt-I9000t
If after updating to 2.3.6 and restoring the applications, the cf root is put, Are the data that I had in the mobile lost?
I have never done it like this, but in theory you should not lose any data or application
Hello
I have just done it. I had problems with 3g, but I called my company (Movistar, Chile) and solved it. However, the phone now cannot find any Wi-Fi network. What I can do?
Thank you very much
Everything is perfect, thank you!!!
Everything is perfect, thank you
Hello friend, I have 1 question and 1 problem, the first is because the battery must be at 100% (since my cell phone for reasons does not charge 100% at most it leaves me at 90% and there is nothing) I think it should to the battery or reason.
The other problem is that I just tried it to see if it connected but it marks me that it does not recognize the device and I tried it on several ports and nothing (I have the kies drivers installed, I have already connected it several times in that way, I activate debugging , and I close everything that has to do with kies by the task manager and I do it in Download mode)
I guess we are talking about the Samsung Galaxy S model GT-I9000?
Sure friend, it's the GT-I900T and I have firmware 2.3.3 with the GINGERBREAD.UMJV2 that's why I wanted to update it but it works for me that's why I go to you.
The GT-I9000T is not the GT-I9000, this tutorial is tried and tested on the GT-I9000, so I don't know what to tell you for your terminal, the best thing is that you stop by sammobile and download everything you need to flash the model of your terminal.
Well then, thanks for your time, I really appreciate it.
In odin, the word COM followed by a number does not appear when you connect it in Download mode?
No, I put it and as it says but it marks me that it does not recognize the device and never detects the COM.
PD.- I will try to see what I do but in your opinion if it manages to connect, do you think it is not a problem with the battery that I mentioned?
Salu2.
the samsung galaxi ace vale callampa
Well if you look at the title of the article this tutorial is for the Samsung Galaxy S not for the Samsung Galaxy ACE.
Your phone will be a Galaxy S model GT-I9000, right?
ayuuuuuuuuuudaaaaaaaaaaaa !! I installed this version of galaxy s but I installed it on a vibrant galaxy s and now it cannot put me in dowload mode since it is not the same ... I need to restore it to the original shape of a vibrant galaxy s .... I hope you can help me 🙂
the cell phone did not turn on after the first pass ... it died! What do I do man !?
I have done this on an i9003 believing it was for this firmware, so on a samsung galaxy scl and it does not start me up or go into download mode !!! What I can do!? it is urgent please
The same thing happened to me, the title of this post is not clear, you can make those mistakes, as I had bought the cell phone recently, it still had a warranty, so I took it to the technical service and when I discovered that it was a logical failure short circuit, they changed it for a new one.
Well, fuck you, you have to read, did you know?
For non-fortune tellers like me: I didn't understand where to put each file, ie csc, modem, etc. And it is because the file does not even contain them, it only has a .tar file that must be placed as if they were all on the PDA, start and that's it. I hope it will serve someone, since few who succeed support those who have doubts. 🙂
But what are you telling me, the tutorial is detailed step by step and within the compressed file are all the files that I specify in the tutorial.
On 10/08/2012 23:06, «Disqus» wrote:
Hello I have a galayx s i9000 2.3.6 from movistar and I would like to know if I can directly install the cf-root JVU kernel to it and if it supports my baseband version I9000BGJV2, Kernel version 2.6.35.7-I9000BGJV6-CL783990 root @ DELL132 # 2 or do I have to install the 2.3.6 JVU firmware first?
Good afternoon I need help…. Well, I followed all the steps to the letter, and my phone connects to the odin, the rectangular window appears in yellow with a number next to it, I click the star button and the process begins, but it only advances if at least 2% both on the odin and on the phone ... above the yellow window in the big square appear the letters FACTORYFS ,,, after up to 15 minutes no further progress ... what would be the solution to my problem ???? THANKS IN ADVANCE …. WAITING FOR YOUR HELP….
Added !!
Enter CS for MD5 ..
Check MD5 .. Do not unplug the cable ..
Please wait..
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
Checking MD5 finished Successfully ..
Leave CS ..
Odin v.3 engine (ID: 5) ..
File analysis ..
SetupConnection ..
Can't open the serial (COM) port.
All threads completed. (succeeded 0 / failed 1)
What is the problem?? : S
Download an older version of odin
Send by Samsung Mobile
Disqus wrote:
Did the previous version of ODIN help you? The same thing happens to me and I don't know what to do? how did you solve?
Go through the process again, being careful where you place the files. And marking repartition first and then when putting the cfroot in mark
2012/10/12
I get this
Enter CS for MD5 ..
Check MD5 .. Do not unplug the cable ..
Please wait..
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
Checking MD5 finished Successfully ..
Leave CS ..
All threads completed. (succeeded 0 / failed 0)
Added !!
Is it over already ??? okay? .. tell me something when you can
Perfect updated !!! no problem.
Thank you very much you are a few stars !!
First of all, thank you very much for the info and the work of writing on servers that are still valid. I'll tell you, I tried to do this same thing with my cell phone about 5 hours ago, I had died, I made a mess, I revived ... I died and with this, step by step I resuscitated ... in reality he became a zombie ... very load fast, it looks extra-liberated because neither the provider's start screen comes out and it says I900, it loads very fast… the problem? The touch screen does not work for me T_T does not recognize my fingers only the buttons that do not serve to configure it 8 square does not say, insert sim check keyboard, etc)
please help!
Funny!
I did not understand anything if there is an easier way to tell me please; _ (
Friend, can you tell me what the pass is.
Once all the steps have been carried out, it asks me "confirm password".
Can you help me, thanks
It does not ask for any pass, did you have the phone locked?
I worked perfectly for me, everything was fine, thanks for the post
Fuck be careful how you can get into a 500 lerus devices like the sambung galaxy 3, it doesn't even occur to me
Hello, everything is super good, the phone works wonderfully but it does not take the 3g, I already configured it from the apn and changed the data band to that of my company, some idea of how to make the 3G return
Activate flight mode and then deactivate it, this should give you a signal.
Thank you very much for the tutoring, it has worked perfectly for me. At first I tried to install the cfroot directly because I already had 2.3.6 and my mobile died ... XD scared me but I started the tutoring from the beginning and not only did my mobile revive but I am already root, thank you very much 🙂
Where is the CF Root file that I downloaded the program to which I supposedly attached the CF Root and I don't get anything help please… ¿?
http://www.4shared.com/zip/62YfB8JY/CFRoot_JVU.html?
Look at the end of the post, there are links for all the programs and files that are needed, and throughout the tutorial it also includes them on several occasions. I recommend that you read the tutorial word by word that everything is very well explained and you don't run the risk of screwing it up like I did at the beginning
HELLO HEY I DISCONNECT MY CELLULAR AND NOW IT DOES NOT TURN ON AAAAAAAAAAAAAAAAH PLEASE TELL ME WHAT TO DO
in which folder is the CF Root ...?
It happened to me as they say below, it also asks me to confirm password, and yes, I had it blocked because I thought it had been stolen and the company blocked it for the imei, but I found it a couple of days ago and While they unlocked it I had thought about updating it but it asks me for the pass, if everything goes well for Monday or Tuesday I have it unlocked since they told me that it takes about 72 hours to unlock it, I can turn it off and when it is unlocked I can put the cf root and the ics? Thanks in advance, apart from this problem, everything else is perfect.
My PC does not recognize the device in download mode, what can I do?
Check if when you open the odin you get the word COM followed by a number in the upper left corner.
On 05/09/2012 04:51, «Disqus» wrote:
What password opens compressed files?
hello .. I have a problem .. I don't have any files to unzip
the code file of the unzipped firmware
the MODEM file
the file named CSC
please I need them urgently
they do not appear when unzipping
Get the zip down again
On 05/09/2012 19:39, «Disqus» wrote:
at the end after three downloads of the zip and with the same problem, see another page and I could solve it ... I could download the files and I had the mobile in semi-lock but it is already solved and with the Rom MIUI Jelly Bean 2.8.24 by muchopoli83 working perfectly..thank you very much for answering and thanks for sharing all this..you do a great job and keep it up ...
Thanks to you friend for your praise and for your support and trust.
On 06/09/2012 22:54, «Disqus» wrote:
I have a question: Is it possible that with this process the IMEI has been replaced? If it could happen that my EFS folder had been deleted and it had been replaced by another, or something like that
My question comes because I did not make a copy of efs (no idea what it was until I informed myself a bit) before following the tutorial, and now the mobile is perfect but it marks me as if I was using roaming, as if it were not out of my mind country, and I have noticed by kies that the firm that I put now says (KOR)
Is it possible that I have lost my IMEI or something like that and have a generic one?
thanks in advance, I am not very knowledgeable in these matters yet
I have followed all the steps that they put and when I get in ODIM3 after finishing all the word PASS the mobile does not turn on it is blocked.
What can I do, there's no way to make it turn on
my phone is samsung galaxy s this hair, it will not let me name it ossuary
Thank you very much uncle, it was perfect for me and everything was very well explained 😉 greetings makina!
I get stuck after using the Odin. The "PASS" thing appears, the phone restarts and begins to install things, but one by one they look like red letters that say "mount fail" on drive E: and there it stays ... what can happen?
That is that some step you have done wrong, in the first step you must select re-partition, and in the second, that of the CFRoot not.
Also pay attention to putting each file in its place.
2012/9/10
This installation is an official software for this model (GT-9000t) ????
If it is a stock
On 11/09/2012 05:30, «Disqus» wrote:
Hello Francisco. My computer is a galaxy S. I did the tutorial to the letter ... however the mobile takes a long time to start, more than 5min and it stays in gsm ... it does not connect me to the internet.
Please can you give me a hand.
Hello Install everything, but my problem is with respect to the touch screen, it is slow .. it responds to the second and somewhat after what I do. Any solution?
Good!
I have done all the steps and I already have the SGS I9000 and I already have it at 2.3.6 with root installed.
The problem I have is that every time I make or receive a call, at the end of the call I get the following error: "The com.andorid.phone process has been interrupted unexpectedly. Please try again" and then I have no coverage for a few seconds. Bluetooth gives me problems and it is very difficult for me to be able to link it with another device.
What I can do?
Do a factory reset to see if it solves you
On 13/09/2012 22:54, «Disqus» wrote:
I have already done a factory reset and I keep getting this error, I have problems with bluetooth and gps when it finds satellites and connects it loses the signal very frequently.
Is there a fix or something to solve this problem?
What happens if the mobile is disconnected? in my case it was left hanging with the black screen I left it for a while and nothing and disconnected it. now it does not turn on what can I do?
Please answer because before writing I have read the comments and more than one. It has happened but I have not seen an answer.
Thank you
Go back into download mode and repeat the process but make sure you have the drivers installed on your computer
On 18/09/2012 13:05, «Disqus» wrote:
This procedure works for Galaxy S I9000T?
No, it does not work.
On 20/09/2012 21:35, «Disqus» wrote:
Thanks so much for the explanation. One of the internet sites where things are explained more clearly.
The only thing that I've had 2 moments where I've gotten stuck:
1. Installing the firmware with odin did not finish the task. In the end, fearing the worst, I disconnected the phone, and tried another version of odin, as you explained in a comment. It was perfect.
2.In the CF root installation it was trying to place the unzipped file on the PDA, when it was not.
In the end, a success.
Excellent friend, I did everything and it came out perfect, now I have facial unlocking and the cell is fast. Thanks
hello a question that I can ask if while I was in download mode disconnect the cell phone, the process does not progress at all, it remains in the sbl.bin part, it has been a while and it does not progress, what can I do?
Try to put it in download mode again and repeat
On 23/09/2012 08:46, «Disqus» wrote:
Hello, such a good day or good morning, you have saved my life but that is why you have uploaded my cell phone, I considered it dead, a person wanted to upload the same post as you but without the csc and they had a very bad phone number those two applications that appeared to me after doing the last step as from cfroot? And how do I get my phone to grab 3g, the internet doesn't catch me, I'm from Venezuela and I have a digitel
Enter wireless connections and configure the apn, if you do not know the data, your company will give it to you
On 29/09/2012 11:09, «Disqus» wrote:
I would like to know if this tutorial works equally well for Samsung Galaxy S Pus. GT-I9001
No it doesn't work
2012/9/30
do not install it, I did it with my samsung galaxy gt-i9000 and it does not turn on !!!!
Before updating it, I read the comments and most of them spoke of a lot of bugs. So I write this to THANK YOU for how well explained EVERYTHING is, and that I have updated it without problems but with a bit of nerves because it was the first time on this mobile. For those who doubt, it is very reliable and if you follow the STEP BY STEP instructions and it works perfectly. Thanks again.
Francisco excellent contribution, carry out the procedure as you indicate it and perfect. Thank you very much for your tutorial for how easy, simple and effective it is.
regards
Give a solution brother, you can't break my cell phone like that!
Can't you change the name of the post saying what model is it for?
PS: now I have a paperweight of 2000 Argentine pesos
The cell phone, as you say, you have broken it by yourself, if you read the post you will realize for which terminal model it is specifically, but of course for that you have to read everything.
How easy it is to blame others for your own mistakes. Having said that, and for you to see my good will, if you tell me the specific terminal model you have, we will see what can be done.
Greetings friend.
2013/3/31
Hello, someone knows how to get the Firmware file when downloading it is the same as the CFRoot, and decompressing it produces a file that says zImage. who can help me?
have you found a solution for this ??? I'm trying but I don't know how to fix it.
It happens to me exactly the same. The CFRoot file and the Firmware is the same. If anyone can upload the correct Firmware or the creator of the post I would appreciate it.
Greetings, I have a problem, I updated to 2.3.6 about 4 months ago, so now jump to the direct step of putting the CFROOT to put 4.1.4, the problem is that it stays on the home screen, the one that says samsung i9000 , turns on, turns off, and so on. Might you help me? Thanks.
Good afternoon, I already did the steps to put the xxjvu version, only that the root can not do it, I do the three buttons and it comes out in recovery mode 3 and how can I return to the download mode
works with gt-i9000b
No dude, this is for the GT-I900 only.
2012/10/15
Does this firmware work with the 9000t? like the root?
No, it is for the I9000
2012/10/15
Hello, very good post !! It works perfect!! I did it but now I want to stop being root and leave the phone as it was with version 2.3.3 of yoigo. and if it is possible to eliminate the counter for the SAT. HOW DO I DO IT ???
You do not need that to send it to the SAT, if you flash the 2.3.6 JVU version again and then do not do the CFRoot part, it will be ready to deliver it to the SAT.
That version is perfectly upgradeable from Kies.
Make sure to do a blanket wipe of the entire internal sdcard.
2012/10/17
So how do I do it ... just like I did to put version 2.3.6 but without doing the CFRoot? I am a bit lost..
Exactly, but it also clears the internal memory of the device
2012/10/18
I installed everything as it says in the Post, and it works very well for me, then I configure the APNs according to my local operator which is Orang Israel, and everything went very well.
Thank you very much, especially for the clarity with which everything is explained, it shows that you invested time in doing it.
Thanks a lot!!!!!!
Thank you very much for the contribution, everything has been perfect for me. Now how do I install ice cream?
Search the blog for the Tsunami X2.5 which is Jelly Bean Android 4.1.2. It is currently the best rom of the moment.
2012/10/28
Many thanks. I didn't want to change my mobile because it was new and I already have it for another season. Congratulations!!!
Now flash it with the Tsunami X2.5 rom and you will have it to the latest version of Android with a superior appearance and functionality.
2012/10/29
I do not know what has failed but after doing the whole process I try to turn on the mobile and only a green message appears ('logo. jpg' draw failed) what can I do to fix it
What terminal do you have?
2012/10/31
Where do I get the file modem and csc I can't find them.
Soso a capo !!!
well ... I have something to ask ... I have completely carried out the steps here exposed, (my mobile is a Galaxy S i9000) and when connecting to Wi-Fi, there is a very rare bug that is that it restarts the connection to every moment ... that is, it disconnects from the wifi and reconnects ... it's a nuisance because sometimes I'm downloading an app and it cuts out ... I have to restart the download ... and not even say in a YouTube video or something like that ... I would like know what it can be? ... if someone knows how to solve it ... in advance, thank you!
Thanks for your tutorial. I was able to revive my Vibrant after an unfortunate brick.
I cannot load the unzipped file of the CF Root (zImage), in the PDA section, because it cannot be found despite being in the folder.
You have to put some kind of extension or something.
Excellent! I did everything as the tutorial and I already have my i9000 updated
Thanks friend
There is no way to download the firmware or the cfroot from the 4shared page, if someone could help me …….
cf-root works for gt-i9000b
and installed everything to the letter, when restarting, the screen went black, now it doesn't turn on, I have galaxy s i9000….
any solution? : /
Redo the process and be careful to do everything the same as in the tutorial, especially the matter of repartition.
2012/11/14
FANTASTIC, thank you very much, installed following the instructions carefully, and the terminal is fully operational and perfect.
Wonderful, perfect, I did it the first time and everything has turned out as you have been saying, we thank you very much for your contribution, you continue to do so, you already have a follower.
Thank you!!!
Good afternoon I have a problem I did what the tutorial said but what happens is that I have a tablet galaxy s model yp-g70 and when I finish the process instead of restarting it remains on a black screen with the samsung logo, could you help me solve that? I'd be very gratefull
Look, you have to try everything again and this time put it back 2.3.6 re partition in odin and wait a while do not disconnect your galaxy s until it turns on the dowload mode and it asks you the language and you can just disconnect it
Hi, I'm in the installation but it already takes more than 10 minutes and it continues in the odin about sbl and it does not advance the last command says sbl.bin pro does not advance and I did everything as the manual says I have verified the steps and now the phone is a samsung galaxy gt i9000t could you help me or say km kitar this and be able to continue with my normal phone ya ke ya panikie me
This is not for the GT-I9000T but rather for the GT-I9000
2012/11/23
According to the firmware to what I had read, there was no variation between the i9000t and i9000 models and the firmware could be updated. So in that I am wrong? Do you know where I can get my original xk firmware and my cell has died
Hello Francisco Ruiz… I have followed the tutorial btal which as you described it but I have the same problem as xpressa t… it does not go beyond the sbl… my team is a GT I9000… I would greatly appreciate if you could guide me and some solution or alternative… Thanks in advance…! !!
Thank you very much, followed to the letter and without problems, saying that at the beginning odin failed, but in the end he got it. Thanks again.
Like silk following the tutorial. I had problems updating with Rom Manager directly from Froyo and at least I have managed to upload to Gingerbread for now 🙂
My question is i9000t applies since when I do the procedure, the yellow line only advances a little bit and then some suggestion is restarted
Hi Francisco, I have a GT-I9000, I have followed the steps, but the first strange thing I have seen was when I first connected the phone to the PC in donwload mode, instead of 1 COM, I got 3 COMs. I have given START and after more than 10 minutes COM 0 was still blank, and COM1 and COM2 have given FAIL, and there they are, what do I do? I don't dare to disconnect the phone from the PC, I wait for your answer
These are the last lines that appear in the window
Odin v.3 engine (ID: 15) ..
Odin v.3 engine (ID: 9) ..
Odin v.3 engine (ID: 8) ..
File analysis ..
File analysis ..
File analysis ..
SetupConnection ..
SetupConnection ..
SetupConnection ..
Can't open the serial (COM) port.
Can't open the serial (COM) port.
You should install the drivers and connect the mobile in download mode.
On 21/12/2012 01:28, «Disqus» wrote:
I solved it, using the odin .83 instead of the .82, now I'm installing the jelly bean 4.1.1 rom, I downloaded the files to the phone and it is installing, but it seems that it takes a long time, doesn't it? I have the gargoyle for a long time on the screen ...
Everything has worked perfectly for me, thank you very much!
works for a samsung GT-I9000b
Francisco: once I have my Nexus 4 operational, I took the Galaxy S and dared to root it…. with your instructions NOT A FAILURE and all in 15 minutes.
Thank you very much for sharing your knowledge.
Now I want to install a Ginger version, if possible 4.2.1 to compare it with the Nexus .. and surely to be disgusted for having spent unnecessarily ..
Any recommendation for this new step?
Follow the tutorial to install RemICS-JB V1.0
On January 8, 2013 17:22 pm, Disqus wrote:
installed and working properly.
Thanks a lot…. your instructions are precise.
After a day of testing, I actually didn't need to buy the nexus4, the galaxy works almost the same …………… .. if you come to Oviedo, give me a touch, I owe you some ciders.
Thanks friend I will keep it in mind
On 09/01/2013 18:55, «Disqus» wrote:
Hello. You can tell me if this is the right thing to do, because I don't get the pass. Thanks
Enter CS for MD5 ..
Check MD5 .. Do not unplug the cable ..
Please wait..
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
Checking MD5 finished Successfully ..
Leave CS ..
All threads completed. (succeeded 0 / failed 0)
Added !!
Hi Francisco, I just followed the step-by-step tutorial and when I restart the phone it asks me for a password, how do I solve this. Thanks
Thanks I just got my I9000 back, following your instructions !!!
Thank you very much friend, everything works perfectly !!! When you go down to Andalusia you have an invitation. A hug
Thanks friend, you know here you have us for any questions.
regards
2013/2/7
well I also did it to the letter and now I do not get any solution network coverage. the terminal was vodafon and released by imei this will have something to do with it. Thanks in advance
You have to configure the APNs with your company data.
This you will find within wireless connections and networks. The data can be found online or by calling Vodafone.
On 12/02/2013 02:00, «Disqus» wrote:
hello, I have a galaxy si 9000 and update to firmware version 2.3.6 Gingerbread, my question is if there is a better version for this phone
hear a question how did you update it as it says here?
and look, I found this one that they say is the best
https://www.androidsis.com/samsung-galaxy-s-rom-android-4-2-1-port-del-nexus-s-rc1-by-elitemovil/
The blue bar in download mode does not change, does it take long? It helps I do not know if to disconnect it and try it with another computer or what to do, I did everything to the letter
Thank you!! I have recovered my cell phone that relieved
olle stays in sbl.bin friend and I don't know what to do please answer
I have to thank you very much for this article because you have saved my galaxy from being a brick since I had tried to root it on the other hand and it was constantly restarting and now it has been like new.
Thank you very much for your collaboration on this page
I have the samsung i9000b, do you know if this also works? There is very little material for this Celu… Thank you !!! everything helps add up !!!!
I followed the steps according to the post but when I restart my phone it stays on the On-screen keyboard settings screen that asks me to tap on a text field and it doesn't go from there, apparently the touch screen stopped working because whatever I do does not accept screen touches ...
What I can do
What is the exact model of your terminal?
2013/3/7
It is the GT-I9000B model
It won't let me do anything on the screen and a next button appears which I can't click because the screen doesn't respond ...
What do you suggest I do?
Thank you very much
Go to sammobile.com and download a firmware compatible with your terminal model since this tutorial is for the GT-I9000.
2013/3/7
Ok Francisco, thank you very much…. I am downloading a compatible firmware from the site.
Thanks to you friend for trusting us
2013/3/7
Hi Carlos, did you get to fix the screen in On-screen keyboard settings ??? I have the same 9000b model and I have stayed in that option ... Or have you done something else ??? Thanks for the reply.
This item is for the i9000 not the i9000B
On 04/04/2013 04:49, «Disqus» wrote:
Hello, I read all this to my phone and it asks me for a password that I don't even know what it is, if the phone was blocked, some solution
And I do everything that it says and now the phone asks for a code for a solution
It will be the SIM code, right?
2013/3/17
I have the sim removed and exo all the steps as you indicate and I confirm the password
Please re-install again
2013/3/18
I installed everything perfectly, I don't have the pad to write or anything, can someone help me?
What is the specific model of your phone?
On 04/04/2013 01:03, «Disqus» wrote:
It's Galaxy S GT-I9000, everything worked for me except the screen
Hello!! I can't get the device to have the new Roteado, the modified Recovery. I have the Galaxy S in Android 2.3.6 I have downloaded the file CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS and I follow the steps you indicate, everything seems correct, but when I try to turn on the mobile I only get the same triangle screen not the menu with the options that should come out. What am I doing wrong ???
Hope someone can help me. Thanks.
Make yours complete and you will not have problems. Above all, note that in the last part you do not have repartition marked.
On 06/04/2013 22:07, «Disqus» wrote:
Hello I have done everything as in the tutorial but without installing the CF-Root I do not want to install it since I have my mobile rooted. but when the process is over and the phone is going to restart, it asks me for a code and it won't let me do anything .. I need help for faa !!!
What model is it?
On April 12, 2013 19:26 pm, Disqus wrote:
the galaxy s i9000
thanks a lot!! I had the phone blocked by imei and could not call or receive calls or anything at all. Is incredible. Just by updating the phone by odin and installing the cf root it has unlocked me and it seems like new! Thank you very much !! 🙂
Hello, I read the whole tutorial and I did everything right, but when the restart is going to be performed, it asks me for a password and not why
This has never happened to me and I have flashed a large number of Galaxy S.
2013/4/15
The same thing happened to me .. what was fixed?
I have added all files as you indicate but it remains in the option ...
Added !!
Enter CS for MD5 ..
Check MD5 .. Do not unplug the cable ..
Please wait..
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
Checking MD5 finished Successfully ..
Leave CS ..
Odin v.3 engine (ID: 4) ..
File analysis ..
SetupConnection ..
Initialzation ..
and it takes 1/2 hour in this way that I do! 🙁 help plss….
THANK YOU ! ! !
Change usb output, sometimes the problem is there
2013/4/15
The same thing happens to me, change the terminal and even the pc, but what can I do?
is it compatible with galaxy s i9003l? I'm already downloading the programs to start! very afraid
Don't even think about trying my friend or you could load the terminal
On 21/04/2013 18:49, «Disqus» wrote:
Hello, good afternoon, the first thing I want to express is my great thanks to the author of this tutorial, I come from being a Blackberry device technician and for me it was always very intuitive to make this type of updates, however the Venezuelan market has been changing to IPhone and Samsung therefore I have to broaden my horizons and that is why I had been looking for a tutorial that more or less would teach me to perform the update as if it were explained to a child, I got this tutorial by following the instructions step by step and obviously checking the GT-I9000 model that is clearly described at the beginning of this tutorial and has been perfect for me, for which I want to thank the tutor once again for his clear and detailed explanation. It worked like a charm for me to accurately understand the update of each application. Salu2 you are already selected in my favorites espro continue posting.
Hello, first of all thanks to all of you who work so hard on things so that we can all enjoy them later.
I want to update the android version of my i9000 but before following the steps I would like to know if I can do it with a version 2.2 froyo.xwJPF or should I first change to another version and then follow the steps described here? The mobile is from Yoigo and I have not touched anything to flash or root
Thank you very much in advance.
Hello, how can I update my galaxy s without installing the custom Kernel with the Root and ClockWorkmod Recovery and it will work for me or I have to install I wait for an answer thanks
Please, I need your help. HIce everything to the letter and when the phone starts to turn on, everything works except the screen, I can't give next. My phone has gone bad? It is the same model, please, I need help.
I have a doubt can this be done on an i9000B?
Odin v.3 engine (ID: 15) ..
File analysis ..
SetupConnection ..
Initialzation ..
Set PIT file ..
DO NOT TURN OFF TARGET !!
Get PIT for mapping ..
Firmware update start ..
boot.bin
sbl.bin
there the odin stays stuck and I don't have abansa, what can I do?
Hello Francisco, I have done the indicated in this tutorial and everything has gone well, except that I have lost the contacts in the agenda, by not indicating at any time that a copy of the contacts should be made before proceeding. Perhaps it would be good if you include this indication for the next people who are encouraged to do so.
anyway, is there any way to get my contacts back?
Thank you.
when it restarts it tells me
confirm password
I can give you urgent help, please
How do I recover the data network ????
Hello Francisco, I always follow you. It happens to me that I have a problem, it hangs on me in the first procedure I have done it more than 15 times and it does not work for me, what can I do, I am a touch desperate because it does not work for me, please help or someone who takes pity on me and me help.
Thank you!!!
This process takes 51 minutes, he wanted to shoot me in the balls
Help, the phone is black, it does not start or it does not go into dowloader or recovery mode, it does not grab the charger. but I can't install it
Excellent information brother, you saved my brother's phone haha
Francisco, good afternoon, I have carried out all the steps, I have given star and in 2 min the FAIL came out! in odin. I have tried to do it again and it appears in the mobile that the phone and the computer have been interrupted. What I can do??
the same thing happened to me
Thank you very much I have updated it correctly, the instructions perfectly explained, thank you
MILLL THANKS EXELENTEEE …… I WORKED TO THE PERFECTION
Nowhere does it say that it is for 9003. If you did not read correctly, do not blame others.
hello friend, eu tenho galaxy s i9000b as faço to install ??
Hello guys, I have been updating the firmware of my samsung galaxy y young, believing that with this process, I would achieve it, and for reasons X, almost to finish updating it, it has turned off suddenly, what can I do as it does not turn on? : S
Hello,
One question, which cf-root should I use to root galaxy gt i9000 with android 2.2 froyo.xwjpf? and especially where can I find the file?
And for the same model but with android 2.3.6 with gingerbread.xwjw9?
Thank you
Thank you very much, I have followed all the steps and I have not had problems. One question, now I get the option to put and remove sound where before I had quick access to connect to the internet ... can that be changed? it is a heavy thing to have to enter networks to activate them each time.
Hello, I have installed firmware version 2.3.6, it is necessary to perform all the steps indicated, or only from the CF root ???
With starting from the CFRoot you have enough.
Hey friend, I have a galaxy pocket gt-s5301l android ics and I was wondering if it is the same procedure to install the firmware to my cell phone, is it the same or not in the firmware installation part?
my selular does not want to cook
Everything worked perfectly following the steps.
Greetings and thank you!.
It works*
I would like you to make a post with the GT-i9000b… Thanks
Thanks Francisco Ruiz, with these steps you can revive my Galaxy S I9000, the root I do it in another way with a Chinese program is fast and safe. Thanks again from Peru.
I did the process and I can't get it to turn on my galaxy s I9000B, any solution? I can't enter the recovery mode, but when downloading ……
Good morning Francisco. I have done the steps one by one with what you indicated. Once OK. It gives a series of errors (I have a photo but I don't know how to send it to you) and the cell phone turns on and off intermittently in the GALAXY S logo. Occasionally it turns on correctly after a long time. how to solve the ignition and errors.
Hello, how about even though your post is old, it is still useful, help us by uploading the files in mega or some long-term server. Greetings
Hello! I need help. I'm sorry to bother you but maybe you can help me. My phone is a samsgung galaxy S GT-I9000, I wanted to free it to use it with another SIM card from another phone company, I proceeded to root it first, I followed the steps in this tutorial: http://androidadvices.com/how-to-root-galaxy-s-on-android-2-3-4-xxjvp-firmware/3/ because my build number ended in XXJVP (I don't remember the rest, I'm silly not to write it down). Using the CF-Root-XX_JVP_AAD_RFS.tar file on the ODIN PDA everything was fine but I received the FAIL message 🙁 I tried again and FAIL came out again, now the phone is bricked with three icons: a pc a triangle with a sign exclamation mark and a telephone. Enter download mode fine. but it does not go beyond there. what I do? I would like to try the steps in your tutorial to flash it and recover it but it scares me very much. Do you think it would work? I do not know which stock firmware to use, I have read a lot but I do not understand, I am afraid of completely losing the cell phone when flashing incorrectly.
I hope you can please help me. I'd be really grateful. I am from Venezuela and we do not have access to dollars, this is my only phone and cell phones cost 10 times more than the minimum wage 🙁
thank you very much for your time to read this
regards
stefi.
My samsung galaxy core i8260l does not take the wiffi, none, they told me that I had to download the recovery, odin and i8260lubamg3, now what do I do ??????????? please help
I have already achieved it the first time !! The cf root file is not read if you load the image directly, you have to load the .rar file (look at the image attached to our crack! 😉)
Thank you very much machine !!
Hi how are things! ps everything was fine until I stayed in download mode, ps yes! when I turn on the phone… .odin recognizes it but when I connect it in download mode it tells me that windows does not recognize it and one of the usb devices is malfunctioning. Any suggestions?
A crap I did everything and I never got PASS. Now screw up the Firmware of the Samsung i9000! This is useless and I did everything as is!
Is there a way to do it with linux, in windows I cannot install odin and my cell phone does not recognize me when I connect it in mass storage mode
I DO NOT LOAD THE RAR FILE IN ODIN PDA SECTION. ANY SOLUTION?
Gentleman, what is the solution when the I9000 equipment does not respond to any combination of keys, neither to enter the download mode nor to the hard reset mode? ... Seriously, I have already tried all the ways I found on the internet but the equipment always turns on normal mode…. Thanks in advance for your reply. Greetings.
Hey friend help I place the files as is and I give it start and it does not advance from
(SBL.BIN
Thanks a lot. Update a Samsung Galaxy i9000t that had android 2.1, you can update it to 2.3.6, with these procedures. Remember the i9000 and i9000t are compatible with their roms. But not for other models. Greetings
I did everything right but when starting it asks me for a password
Ma tean, kuidas suhted on meie elus olulised ja kui palju me tahame pot õnnelikud armastatud inimesega, mõnikord pole see lihtne. Me kõik näeme vaeva oma armuelu parandamisega ja oleme lihtsalt õnnelikud.
E-post: (info @ spelloflife.org)
või Külasta: www .spelloflife. org
Kui vajate oma suhetes abi.